Quick Answer: How Much HP Does A Vortec 350 Have?

How much horsepower can you get out of a 5.7 Vortec?

You can install the 383 with Vortec heads on it.

The HT383 that was available from GM uses Vortec L31 heads, the GMPP 383 shortblock and the Ramjet 350 roller cam with specs of 196°/206° duration at 0.050″ lift and 0.431″/0.451″ of lift on a 109° LSA produces 340 hp@4500 and 435 lb/ft of torque at 4000rpm..

How can I get more horsepower out of my 350 vortec?

No matter what application your Chevy 350 motor is in, a few simple steps can get you more better performance and higher horsepower.Modify your air intake. … Modify your exhaust. … Change your camshafts and valve train. … Purchase new cylinder heads, or have yours ported and polished. … Have your motor rebuilt and blueprinted.

How much horsepower do headers add to a 350?

The length of the primary tubing determines the effective rpm range, but headers can be worth 15-20 hp on the right application. Run on our restrictive two-barrel 350, the headers improved the power output to 248 hp and 365 lb-ft of torque, with consistent gains through the rev range.

What year is the best Chevy 350 engine?

L31 (2002) From a purely technical standpoint, the most recent version of the Chevy 350 would naturally be the best of the bunch. Marketed as the “Vortec 5700” engine, but known internally by the moniker of L31, this engine was used primarily in GM vans and trucks until 2002.

How many miles will a 350 Chevy last?

229k miles is not unheard of for a properly maintained 350. You could do a compression test and leak down test to analyze the health of the motor.

Is the 350 Vortec a good engine?

The best-known and most-beloved has to be the “350” or 5.7-liter version; especially with Chevrolet and GMC trucks. They are powerful, tough, reliable and it is relatively easy to “soup up” or increase their performance.

How much horsepower does a 350 Vortec engine have?

Chevy 350 Engine Specs The Chevy 350 engine is a 350 cubic inch (5.7-liter) small block V8 with a 4.00 and 3.48 inch bore and stroke. Depending on the year, make and model of a car, horsepower ranges from approximately 145 to more than 370.

What is the difference between a 350 and 350 vortec?

Vortec heads instantly added 55 or more horsepower to a regular 350 head with the same displacement. Automotive enthusiasts are quick to note that the 350 and the 5.7 Vortec are essentially the same engine with the same displacement. The 350 designation is the cubic inch measurement that also translates to 5.7 liters.

How big of a cam can I put in a stock 350 vortec?

Unmodified heads w/stock retainers and seals will allow somewhere between 0.420″ and 0.470″ lift- but this has to be verified on a per head basis.

Can I put Vortec heads on a 350?

night rider Veteran Member. Yes the 1996-02 L31 350 vortec heads will bolt to ANY gen 1 350 engine.

Can you put 400 heads on a 350?

400 heads on a 350 block is a great way to increase your midrange and top end power. The swap is a direct bolt – on deal, you just need to be sure to use 400 head gaskets when you do the swap.

How much horsepower will Headers add?

10-20 horsepowerIn general, a quality set of headers should provide an increase of approximately 10-20 horsepower, and if you’re restrained with your right foot, you may even see an increase in fuel mileage.

Why is a 327 better than a 350?

In the vehicle, it’s more of a matter of “gearing” than revs. A 327 with it’s shorter stroke would need shorter gears so it can GET to its revs, where a 350, with its slightly longer stroke and more torque output will pull a little taller gear than the 327 will.

How much HP can a 4 bolt main 350 handle?

1. 4-bolt blocks with OEM main bolts are good to 475 HP, and are good to 7200 RPM. 2.